Location Of Electric Equipment In Passenger Compartment
1 - Relay board with fuse holder 2 - Accelerating enrichment control unit for oxygen sensor 8 - Neutral Park and backup light switch automatic Location of Electric Equipment in Passenger Compartment
Ground Points On Car
4. Ground on left front side member. 1. Battery ground negative pole to body. 4. Ground on left front side member. 5. Ground on right front side member. 5. Ground on right front side member.
Servicing Automatic Antenna Mast
Clean a fully run out antenna mast with a low viscosity, non-resinous oil or a cleaning spray, e.g. MS-2 spray. We recommend antenna cleaning cloths, which could also be used by customers without problems. Run antenna mast in and out several times, and wipe off any dirt each time. Replace the mast, if mast parts are deformed or antenna movement is still difficult after cleaning thoroughly. If the mast movement is still difficult, i. e. antenna mast does not run out or in fully, after handling...
Removing And Installing Windshield Wiper Motor
3. When installing, connect the plug and turn on the ignition before securing the linkage. Move wiper arms to off position and mount linkage. 4. Check function on a wet windshield. Correct wiped area if necessary. 2. Unscrew wiper linkage, disconnect plugs, unscrew motor, remove mounting screw on frame, lift frame slightly and take out motor. Removing and Installing Windshield Wiper Motor
Removing And Installing Wiper Arms
1. Remove cap and unscrew hexagon nut. Note washer 2. Fold up wiper arm and take off of shaft by carefully moving back and forth. Do not pry off. 4. Check operation on wet windshield. The wiper blade should not contact the ornamental frame of the windshield on the driver's side. 3. Adjust wiper arms so that they rest on upper edge of dark strip in off position. Install wiper arm with spoiler on driver's side.
Removing And Installing Outside Door Handle
1. Loosen self-locking screws on door frame. 2. Slide outside door handle forward and detach at outside door panel. When the door lock is mounted and the door trim is installed, the operating lever can be engaged with the door lock by inserting a screwdriver, the tip of which is bent, through an opening in the outside door panel. 3. Detach operating lever with installed door lock . 1. Stick liners on outside door handle. 2. Install and bolt outside door handle with operating lever making sure...
Installing New Version Rear Side Panels On Cars Prior To 198 0 Models
Only the new version rear side panels from 1980 models are available for replacements. Or, depending on extent of damage, weld in a new reinforcement. After using up stocks of old version parts in cars prior to 1980 models, the new version rear side panel will be applicable to all models. The following additional procedures will be necessary to install the new version parts in cars prior to the 1980 models. 1. The striker pin base has been made 4, 5 mm deeper so that the longer pin from the...
Door Lock New Version From 1980 Models
The door lock inner part, door lock outer part and striker of Type 928 are used in all models as from 1980 models. The only deviation from the 928 version is a modified connecting lever for the door lock inner part on the passenger's side. The connector for the door lock inner part is located on the door outside handle. The door lock outer part must be bolted to the door lock inner part in opened state, since otherwise the connecting lever would be damaged by the release pin of the door lock...
Extra Wiring Diagram For Air Conditioner
2 - Refrigerant compressor 4 - Fresh air blower switch 5 - Air conditioner switch 8 - Condensor blower relay 16 - To ignition switch terminal 15 17 - To ignition switch terminal X A, E, Gf H - Central electric multiple plugs
Service Installing Strap For Removable Roof Panel
The removable roof panel can be set up on the fasteners while driving, if a strap is installed from the roof panel to the body. This strap will prevent the roof panel from lifting at the rear when driving on rough roads. 3. Lift trim at rear and insert a reinforcement plate. Then mount strap with a black 3,9 x 16 mm sheet metal screw and cloth covered washer. 6. Install roof, lock and clip on the strap. 1. Remove roof panel and press plastic rivets out of the roof trim in the rear area. 4....
Service Installing Car Radio
1. Drill hole in fender according to mm dimensions shown. Drill with an antenna cutter hole saw so that the mounting threads of the antenna can be easily pushed through in vertical position. 2. Guide antenna in from below and secure. Make sure that antenna is vertical. Guide antenna cable toward inside through one of the available holes and locate it at the center console. Dimensions in brackets refer to an automatic antenna. 1. Remove side trim next to rear seats. 2. Guide cable through...
Location Of Electric Equipment In Engine Compartment
1 - Ignition control unit Ignition control unit with EIS 2 - Low pressure switch air conditioner 3 - Idle stabilizer connection point 5 - Air conditioner compressor 6 - Frequency valve oxygen sensor 7 - Mileage counter oxygen sensor 8 - Brake fluid level transmitter 9 - Control pressure regulator 11 - Alarm system contact switch Location of Electric Equipment in Engine Compartment 17 - Temperature switch warm start 21 - Temperature time switch for cold start valve 22 - Coolant temperature...
Removing And Installing Speedometer Drive Cable
4. Pull out and fold down instrument panel. Disconnect drive cable on speedometer. 1. Remove cover on left front wheel hub. Remove circlip on drive cable. 2. Pull out drive cable on inside of steering knuckle by hand. 5. Pull iower drive cable end into upper section of engine compartment. Remove rubber grommet and pull off of drive cable. 2. Pull out drive cable on inside of steering knuckle by hand. 5. Pull iower drive cable end into upper section of engine compartment. Remove rubber grommet...
Removing And Installing Bumpers
The front and rear bumpers are bolted to the bumper brackets with 2 each M 10 x 60 hexagon head bolts, plain washers and lockwashers. Fog lights and turn signals can either be removed with the front bumper, or removed separately. Fit and mount bumper brackets parallel to the body contour. The rear bumper and bumper brackets are mounted in the same manner.
Installing Stay In Removable Plastic Roof Panel
Starting with Chassis No. 924 720 5639 threaded sleeve Part No. 477 871 763 and are installed in plastic roof panels to prevent wind noise and maintain the front roof shape. Service installation of stay is required in a plastic roof panel if the outer surface protrudes past roof edge at front or depressions are visible at the fasteners. 1. Unlock and remove roof panel. 2. Remove roof panel liner by prying out rivets and removing screws of front fasteners and at front center. 4. Guide in stay...
Removing And Installing Remote Control Outside Mirror
1. Remove bezel from door panel. 3. Loosen nut with Special Tool 9158. Remove bezel. 1. Remove bezel from door panel. 2. Pull off adjusting lever knob or press off with a suitable tool if necessary. Remove rubber dust cover and retaining ring over the adjusting lever. 3. Loosen nut with Special Tool 9158. Remove bezel. 6. Loosen outside screw on mirror and remove the mirror. 4. Remove door panel. Pull off plastic sheet from door partially. 5. Bend open metal tab of reinforcement plate and guide...
Repairs With Set Ens 224300 Attachment
These attachments can be applied to simple repair jobs of bodies with medium front and rear end damage. Remove Front and rear bumpers with brackets Front apron All damaged body parts as required by repair work Torsion plate covers and outer rubber mounts. Also remove running gear and engine depending on type of damage. Preparing Celette stand Mount cross member for rear axle attachments and supports for longitudinal Bolt attachments to rear axle cross tube. Bolt attachments to rear axle cross...
Info Pff
Fan relay Fuel pump relay Air conditioner relay Headlight cleaner relay Seat belt warning relay Rear window defogger relay Bridge term. 56 - 56 b Extra high beam relay Horn relay - Intermittent wiper action relay - Turn signal emergency flasher relay Location of R lays - From 1981 Models 90 - 4 c FUSES FROM 1981 MODELS FUSES IN EXTRA FUSE BOX FROM 1981 MODELS 6 Stop lights, concealed headlight 8 motor, hazard light system 7 Inside light, radio, cigar lighter, clock 8 trunk light 8 Turn signals,...
Alarm System 924
The alarm system is turned off and on with a separate key. The alarm switch is located in the side panel behind the driver's door lock. The key has to be turned to vertical position to turn the system off. Spare keys are not available for the alarm switch. If the key is lost, the alarm switch must be replaced. The key must be turned to horizontal position to turn the system on. The alarm would be set off by opening the driver's or passenger's door, trunk lid, engine hood and After setting off...
Preparing Body For Application Of Basic Straightening Attachments
Bumpers with brackets or front rear impact absorbers Front apron All damaged body parts as required for straightening work Also remove engine, if front end of car is seriously damaged Prepare Celette stand Mount all attachments of straightening set, except bumper attachments. Loosen mounting bolts on spring strut domes to place body on Celette stand. Note Check horizontal position of Celette stand with a water level. Install bumper attachments only after positioning body. Mounting point on...
Removing And Installing Window Guides
2. Pull out window guides in door recess and All window guides are cut to proper length, so that they must be fitted properly by stretching or pressing. 4. Install outer window recess rail, assuring a neat fit with the end of the ornamental frame. 3. Remove outside window recess seal with ornamental strip. 1. Press lower front and rear window guides into guide rails and check for a neat fit 2. Slide on ornamental frame for upper door frame. Bend down the metal tongue behind the opening. 3. Coat...
Info Jip
Oil dipstick guide tube, installing 17 - 4 a Oil filter, removing and installing 17 -8 Oil pressure and oil pressure switch, checking 17-5 4-speed manual transmission 088 A 5-speed manual transmission 016 Y 5-speed manual transmission 016 9 - 1980 5-speed manual transmission 016 9 - 1981 Automatic transmission refer to page 37 - 01 Clutch, removing and installing Type 088 A Clutch, removing and installing Type 016 Y Clutch, removing and installing Type 016 9 Clutch disc, removing and installing...